Switch the Zivio ON or OFF

To switch ON, press and hold the Power button for several seconds. The indicator light will flash GREEN when the Zivio powers on and then either alternating RED BLUE RED to indicate it is in pairing mode or STAY OFF to indicate that it has paired with another device that it has previously paired with.

To switch OFF, press and hold the Power button . The indicator light briefly flashes RED before the Zivio shuts off. Your device may let you know that it has dropped the connection with the Zivio.

Checking battery level

To check the battery level, tap the Power button . The indicator light will briefly flash the current power level, with BLUE meaning fully charged, PURPLE meaning partly charged, and RED meaning low battery .

Buttons Cheatsheet

Tap = less than ½ second,  Press = about 1 second,  Hold = more than 4 seconds

Power ON/OFF	Hold Power button and Volume Up button simultaneously
Check battery	Tap Power button
Enter pairing mode	Hold Joby button
Answer calls	Tap Joby button
End calls	Press Joby button
Volume control	Tap or Press Volume Up button or Volume Down button
Mute the headset	Tap or Press both Volume Up button and Volume Down button simultaneously
Reject an incoming call	Double-Tap Joby button
Transfer Audio from Zivio to phone	While on a call, Double-Tap Joby button
Transfer Audio from phone to Zivio	While on a call, Double-Tap Joby button
Redial last number	Press Joby button
Enter multi point mode	Tap Joby button and Power button simultaneously

Three-way calling (TWC)

If you receive another call while already on call, the Zivio will emit an audio tone, to send new caller directly to Voicemail Double-Tap the Joby button. To place your current caller on hold and take new call, Tap the Joby button once.

You can toggle between active and held calls by tapping the Joby button.

Accept incoming call and drop current call	Press Joby button
Place active call on hold and accept incoming call	Tap Joby button
Toggle between active call and call on hold	Tap Joby button
Start a conference call	Double-Tap Joby button

Call handling

To make outgoing calls or answer incoming calls, use your phone as you would normally. A GREEN indicator light will flash slowly during the call.

If your phone supports voice dialing, double-tap the Joby button and speak into the Zivio microphone to place a call.

To answer an incoming call, tap the Joby button or use phone's answer button.

To end a call, press the Joby button or use the phone button.

Adjust the earphone volume

During a call, press the Volume Up button or Volume Down button to increase or decrease the call volume, respectively. To adjust the volume quickly, press and hold the button in the desired direction.

Protect your hearing!

Using the Zivio at extremely high volumes could potentially cause damage to your hearing. Use caution and operate at a reasonable, comfortable volume.

Mute or unmute the microphone

To mute or unmute the microphone during a call, press both of the Volume buttons simultaneously. A long tone is played, and the Zivio will beep at regular intervals until the microphone is unmuted.

Disconnect the Zivio from the phone

There are three ways to disconnect the Zivio from your phone:

– Switch off the Zivio.

– Disconnect the Zivio in the Bluetooth menu on your phone.

– Move the Zivio more than 10 meters (30 feet) away from the phone.

(You do not need to delete the pairing with the Zivio to disconnect it.)

Reconnect the paired Zivio to your phone

To reconnect the Zivio to your phone, power on the Zivio and use your phone’s menu to connect it. Most modern phones (as of Bluetooth version 1.1) will connect to the Zivio whenever both devices are powered on and available.

Using the Zivio with several devices

You may use your Zivio with multiple devices at the same time by enabling the multi point feature. First, pair your Zivio to the two devices. Next, enter multi point mode mode by simultaneously tapping the Power and Joby buttons. The Zivio will flash green indicating it is connected to both devices. The Zivio will only transmit audio through one device at a time, but will be able to transmit audio on either device as long as they are both within range.

Clear Zivio settings

To clear all settings from the Zivio (for example, the list of paired devices), press and hold the Power and Volume Up buttons simultaneously for 10 seconds.

Turn off the blinking indicator lights

You can stop the Zivio indicator lights from blinking during calls by toggling the "Call in Progress" lighting. To do so, press and hold the Joby and Volume Down buttons simultaneously for 3 seconds. The indicator lights will still flash during pairing or if there is a low battery charge.